Audio failures are generally divided into two categories: one is caused by improper use, and the other is caused by the weather. The main factors that affect the normal work of car audio in late summer and early autumn are high temperature and humidity. Because the car audio is mostly installed in the upper part of the dashboard, in order to avoid the exposure of the sun, the effect of using sunshade is better. If the door and window sealing strip is not strict, it should be replaced, otherwise the loudspeaker is easy to rust and damage, or even cause short circuit to burn the main engine. With the coming of the rainy season, the humidity increases, and there is often a layer of fog on the surface of CD records, which makes it difficult to read the disc. It is best to scrub it every once in a while. If the CD drive is modified, in order to avoid dampness, do not install it under the floor and seat, preferably on the high part of the car body, but not on the rear windshield, too high temperature will accelerate the aging of electronic components and laser head.
Generally speaking, about 150000 of the models in the interior of the advanced sense and materials, there will not be so much sincerity. In terms of materials, the X90 dragon uses 118 kinds of interior materials for dashboards, carpets, door guards, ceilings, posts, steering wheels, damping mats, seats, sunshades, etc., and is also equipped with CN95 air conditioning filter elements, dual-channel laser PM2.5 sensors and negative ion generators to ensure the air quality in the car. In terms of these materials and configuration, it can be said to be quite kind.
Rear bumper, dashboard, etc. Body and body parts: body shell, hard shell roof, floor, door, radiator grille, front end plate, flow stopper, baggage warehouse cover, sunshade, wing panel, engine cover, headlamp mirror, etc. Parts under the engine cover: air conditioner shell, air guide cover, intake pipe cover, fan guide ring, heater cover, water tank components, braking system components, battery bracket, engine sound insulation board and so on. Interior decoration parts: door interior panel, door handle, dashboard, steering rod parts, mirror frame, seat and so on. Such as pump cover and other electrical components and gear sound insulation board and other drive system parts. Suspension parts: front.
6. the interior and exterior decoration engineering design the automobile interior and exterior decoration includes the automobile exterior decoration and the interior decoration, because it is also called the body accessory equipment because it is installed on the body. The main design of exterior parts includes front and rear bumper, glass, door anti-collision decoration strip, intake grille, luggage rack, skylight, rearview mirror, door mechanism and accessories and sealing strip. The interior design mainly includes dashboard, steering wheel, seat, seat belt, airbag, carpet, sidewall interior decoration, sunshade panel, handrail, car rearview mirror and so on.
The structure of the window should be able to control sunlight exposure and limit the area ratio of the window wall. For buildings with larger window area, endothermic glass, heat reflection glass or shading measures should be considered, such as sunshade panels, eaves, eaves, balconies, blinds, curtains and so on. Natural air can be directly used as a source of energy when the outdoor temperature is low, so the structure of the window should be able to open or set a natural vent on it.
Open the sunshade on the soft grass and have a private cool space every minute ~ spread the carpet, then arrange a well-prepared picnic and delicious Decathlon snacks. Happiness is as simple as that ~
However, because the bubble body is a poor conductor of heat, the cooling process often shows that the surface bubble body has been cooled and solidified, while the temperature of the core bubble body is still very high, assuming that the cooling setting ends at this time, although the bubble body has been solidified and shaped on the outside, but the core is still at a high temperature, and its heat will continue to transfer, raising the temperature on the surface of the bubble body. Coupled with the expansion force of the core bubble, it is possible to deform or split the stereotyped bubble. Therefore, for EPP manufacturers, it is necessary to ensure a sufficient cooling setting time for the cooling and curing of foamed products. In areas where higher working temperature is needed, EPP foaming material is more advantageous than PE foaming material, such as sunshade panels, insulation panels of instruments and places where the temperature between the doors is easy to rise.
Lan Wenping and his entourage successively inspected five residential areas, including Yonghuafu House in Jianyuan District, Chunjiang New Town Phase I in Yuhuatai District, Keyuan Garden and Yinlong Yayuan in Qinhuai District, and 48 Zhongling Street in Xuanwu District, and sent cool oil, elixir, towels, sunshade hats and other heat prevention and cooling items to the property management and renovation staff of the old district. They told everyone to do a good job of personal protection, avoid high temperature periods, and arrange working hours reasonably. Do a good job in heat prevention and cooling, and urge construction units to take effective heat prevention and cooling and protective measures in time to ensure the safety of front-line workers in the transformation of old residential areas, so as to ensure that the renovation project of old residential areas in the city is carried out in an orderly manner. After the condolences, Lan Wenping and his party went deep into the unit corridor to check the long-term management of beautiful homes, requiring property enterprises to further improve the level of property services, create a comfortable and safe living environment for owners, and effectively meet the livable needs of the people.