Most of the car is made of delicate leather, metal and wood, needless to say the degree of meticulous workmanship. The dashboard connects with the wooden veneer of the car door to form a continuous curve, creating a sense of intimacy similar to sitting in the living room at home. All the wood decorations are made by hand, then hardened for 72 hours, and finally coated with varnish, so that the natural beauty of the wood can be better presented. The new interior contains 600 new parts, while a few parts, such as sunshades, door handles and seat armrests, are the same as those of the previous generation.
Changshu Auto Decoration announced that the company or subsidiary company intends to set up a new wholly-owned subsidiary in Hefei, Anhui Province, with self-raised funds, with an investment of 2 billion yuan to build auto parts production plant and other projects. The project is divided into three phases, and the investment in the first phase is expected to be about 496 million yuan, of which the investment in land and fixed assets is expected to be about 346 million yuan. The project mainly includes: construction of auto parts production plant, R & D center, office building, production of car door guard assembly, dashboard assembly, auxiliary dashboard assembly, sunshade assembly, column assembly and other parts products.
First, the sanitary disinfection of the enclosure should be done well. The manure should be cleaned up in time every day and transported to a place far away from the cattle farm for accumulation and fermentation, and the cowshed should be disinfected regularly, usually once every 3-5 days in summer and autumn, and once every 7-10 days in winter and spring. Second, strengthen window ventilation to reduce toxic and harmful gases such as humidity, dust, ammonia and carbon dioxide in the enclosure. Third, to ensure that the barn temperature is suitable, sunshade net is set up to cool down in summer, and greenhouse is built to keep warm in winter, only beef cattle can grow better at a suitable temperature.
The exterior sunshade of the building is specially designed, which fully considers the difference between summer and winter, meets the enhanced shading performance in summer and the enhanced heat performance in winter, and greatly reduces the energy consumption of air conditioning and heating in the whole year. Figure 1 shows the exterior sunshade used in the building. The whole building adopts non-thermal bridge design, and the thermal bridge coefficient ψ a ≤ 0.01W/ (m ·K). Figure 2 is a simulation diagram of the temperature distribution of the thermal insulation effect of the peripheral structure nodes.
On a hot summer day, some items in the car, such as perfume seats, lighters and cans, can easily explode when exposed to the sun for a long time, so for the safety of the car, the sun shade is used to block the sun and protect the safety of the car, with the sunshade facing outward, so that the sun can be reflected and the heat absorbed can be reduced.
Since the condenser of the window air conditioner is air-cooled and located on the outside of the wall, if the sun shines directly (especially at 2: 00 p.m. is the peak time of the cooling load required by the room, and the temperature of the outer wall and the surrounding space is also the highest), it increases the tears on and around the condenser, and the heat dissipation effect of the condenser decreases, resulting in an increase in condensation temperature, resulting in an increase in condensation pressure. The cooling capacity of the system decreases, the power consumption increases, the current increases with the increase of load, and the overload protector is overloaded for a long time, which leads to contact sintering, loss of protection function and compressor burnout. The position of the sunshade should not only block the direct sunlight, but also can not block the hot air out of the air conditioner, so that it can release the heat to the atmosphere without hindrance. The distance between the rear barrier and the window air conditioner should be more than 1.5m. The left and right and upper barriers should be left from the air conditioner! Add coffee and above,
This is a high-rise residential building with many levels of changes on the facade and two external shading methods are used on the windows. One is a lightweight perforated metal sunshade picked out from the outer wall, one neatly arranged on the outside of the window, keeping a great distance from the outer wall. This kind of baffle sunshade can effectively block the low-angle sunlight projected from the front of the window. The surface of the sunshade is painted red and stands out on the facade. Another way is that the upper entrance of the window hole and the U-shaped sunshade panels with horizontal and vertical shading on both sides of the window can effectively block the sunlight projected from the front and side of the window. The exterior of the U-shaped sunshade is painted white, in sharp contrast to the red of the metal sunshade.
The concentrated display area of the curtain wall technology is also rich in bright spots, in which the tower curtain wall adopts the external sunshade technology, and the sunshade board is designed at the angle of the west sun on the outside of the curtain wall, which can prevent the solar radiation heat from entering the room from the glass window in summer and prevent the indoor heat from escaping from the glass window in winter, saving about 10% of the building heating energy consumption.